1

Neuthane 100 & 2100 Series

 
High Performance Cast Elastomers ….
Neuthane 100 and 2100 Series 

Neuthane Series 100 & 2100 Products on this page...

Catalyst Neuthane Product number Neuthane Photolibrary
reference
Shore A Shore D click on reference  
Neuthane 100 Series        TDI-PTMEG Ether Prepolymer 72 CA6 122
  78 MOCA 122
84 MOCA 128  
83 MOCA 128S  
80 E300 (CA6) 128S  
85 MOCA 132  
85 MOCA 132S  
90 37 MOCA 143  
89 E300 (CA6) 143S  
94 43 MOCA 155  
94 43 MOCA 155S  
95 47 MOCA 163  
95 47 E300 (CA6) 163S  
Neuthane 100 Low Viscosity Series 83 MOCA 128SLV
90 37 MOCA 143SLV
64 E300 (CA6) 164LV
75 MOCA 2192LV
70 E300 (CA6) 219 2LV
<  Neuthane 100 Series TDI – PTMEG Ether Prepolymers 82 MOCA 127
  90 MOCA 142
   88 E300 (CA6) 142
  93 MOCA 153
  95 MOCA 162
 
<  Neuthane 2100 Series Low Odour TDI – PTMEG Ether Prepolymers
85 MOCA 2132
90 37 MOCA 2143
94 43 MOCA 2155
95 47 MOCA 2163

 

 

High Performance Cast Elastomers    
Neuthane 100 Series TDI – PTMEG Ether Prepolymers (72 – 85 Shore A)

Properties

The Neuthane 100 series are high performance TDI – PTMEG ether prepolymers designed to produce items for use in arduous application areas.

  • a high level of physical properties
  • very good dynamic performance
  • good hydrolysis resistance
  • ease of use
  • low viscosity
  • choice of normal or long pot life grades
  • hardness range from 70A-95A
  • Wheels (e.g. fork truck, pallet truck and press on bands)
  • High load roller coverings (e.g. steel & paper industry)
  • Mining and quarrying (e.g. screen decks)
  • Hydrocyclones
  • Oil and gas industry (e.g. gaskets)
  • Automotive (e.g. suspension bushes)
  • Pipe-linings
  • Metal Finishing (e.g. vibration bowls)

Processing can be by hand or by dispensing machine

  • Melt prepolymer at 50-70°C for 12-24 hours (as a guide the grades with the lower NCO value will take  longer to melt than those with higher NCO values)
  • Heat the prepolymer and curative to the recommended temperature
  • Add pigments and Antifoam, as applicable, whilst mixing
  • It is recommended that air be removed from the prepolymer under vacuum prior to addition of the curative
  • Add the curative and thoroughly mix ensuring that no unmixed material is left on the container sides (if necessary the mix can be transferred to a second clean container and mixed again)
  • Remove air under vacuum
  • Cast into moulds, preheated to the recommended temperature
  • Cure as recommended
  • Avoid prolonged storage of prepolymers at  elevated temperatures. This will result in low  hardness and lower properties of the cured material
  • Avoid moisture contamination of all materials
  • Part used containers should be flushed with dry  nitrogen and resealed immediately after use
  • ‘LV’ grades available for certain hardness’s  allowing easier processing due to lower viscosity.
  • Solvents/Abrasion – ester based systems should be considered: Neuthane 200 [TDI] or Neuthane 700 [MDI]
  • Humid/Wet – MDI or Aliphatic Isocyanate based systems should be considered: Neuthane 600 [MDI]
    or Neuthane 500 [Aliphatic]
  • Resilience – improvements can be achieved with MDI based systems: Neuthane 600HR
  • Cost – Neuthane 100 [PTMEG/PPG], Neuthane 300
  • [PPG] or Neuthane 200 [Ester] can be considered

To view the full width of the table, turn your mobile to landscape.

Neuthane 100 Series TDI – PTMEG Ether Prepolymers (72 – 85 Shore A)

Neuthane 122 122 128S 128S 128 132S
%NCO (mid-point) % 2.2 2.2 2.8 2.8 2.8 3.4
Curative CA6 MOCA MOCA E300 (CA6) MOCA MOCA
Recommended Stoichiometry % 95 95 95 95 95 95
Mix Ratio Curative per 100 Parts Resin by weight 5.3 6.6 8.5 6.8 8.5 10.3
Resin Temperature °C 80 80 75 70 – 80 75 75
Curative Temperature °C 40 110 110 40 110 110
Recommended Mould Temperature °C 100 100 90 100 90 90
Viscosity @ 100°C cps 840 840 800 1000 920 420
Pot life (on a 500g mix) minutes 12 15 18 12 13 17
Recommended Cure Temperature / Time °C / hrs 100 / 16 100 / 16 100 / 16 100 / 16 100 / 16 90 / 16
Hardness DIN 2240-91 Shore A 72 78 83 80 84 85
DIN 2240-91 Shore D
100% Modulus BS 903 Pt A2 – ISO 37 lb/in²
(Mpa)
500
(3.4)
510
(3.5)
700
(4.8)
810
(5.6)
840
(5.8)
300% Modulus BS 903 Pt A2 – ISO 37 lb/in²
(Mpa)
900
(6.2)
840
(5.8)
1340
(9.2)
1250
(8.6)
1450
(10)
1600
(11)
Tensile Strength BS 903 Pt A2 – ISO 37 lb/in²
(Mpa)
3700
(25.8)
4000
(27.6)
4150
(28.6)
3300
(22.8)
4500
(31.0)
4200
(29)
Elongation at Break BS 903 Pt A2 – ISO 37 % 630 600 530 400 510 510
Tear Strength BS 903 Pt A3 – ISO 34-1 lb/in
(KN/m)
360
(63.0)
370
(64.8)
400
(70.1)
360
(63.0)
420
(73.5)
380
(66.5)
Compression Set BS903 Pt A6 – ISO 815 % 27 22 30 25 38
Abrasion loss DIN 53516 mm³ 52 32 48 38 59
Resilience ASTM D 2632-92 % 62 59 54 63 46
Specific Gravity g/cm³ 1.05 1.05 1.06 1.06 1.06 1.07
Neuthane 122 122 128S 128S 128 132S
%NCO (mid-point) % 2.2 2.2 2.8 2.8 2.8 3.4
Curative CA6 MOCA MOCA E300 (CA6) MOCA MOCA
Recommended Stoichiometry % 95 95 95 95 95 95
Mix Ratio Curative per 100 Parts Resin by weight 5.3 6.6 8.5 6.8 8.5 10.3
Resin Temperature °C 80 80 75 70 – 80 75 75
Curative Temperature °C 40 110 110 40 110 110
Recommended Mould Temperature °C 100 100 90 100 90 90
Viscosity @ 100°C cps 840 840 800 1000 920 420
Pot life (on a 500g mix) minutes 12 15 18 12 13 17
Recommended Cure Temperature / Time °C / hrs 100 / 16 100 / 16 100 / 16 100 / 16 100 / 16 90 / 16
Hardness DIN 2240-91 Shore A 72 78 83 80 84 85
DIN 2240-91 Shore D
100% Modulus BS 903 Pt A2 – ISO 37 lb/in²
(Mpa)
500
(3.4)
510
(3.5)
700
(4.8)
810
(5.6)
840
(5.8)
300% Modulus BS 903 Pt A2 – ISO 37 lb/in²
(Mpa)
900
(6.2)
840
(5.8)
1340
(9.2)
1250
(8.6)
1450
(10)
1600
(11)
Tensile Strength BS 903 Pt A2 – ISO 37 lb/in²
(Mpa)
3700
(25.8)
4000
(27.6)
4150
(28.6)
3300
(22.8)
4500
(31.0)
4200
(2.9)
Elongation at Break BS 903 Pt A2 – ISO 37 % 630 600 530 400 510 510
Tear Strength BS 903 Pt A3 – ISO 34-1 lb/in
(KN/m)
360
(63.0)
370
(64.8)
400
(70.1)
360
(63.0)
420
(73.5)
380
(66.5)
Compression Set BS903 Pt A6 – ISO 815 % 27 22 30 25 38
Abrasion loss DIN 53516 mm³ 52 32 48 38 59
Resilience ASTM D 2632-92 % 62 59 54 63 46
Specific Gravity g/cm³ 1.05 1.05 1.06 1.06 1.06 1.07
High Performance Cast Elastomers     
Neuthane 100 Series TDI – PTMEG Ether Prepolymers (85 – 95 Shore A)
Neuthane 132 143S 143S 143 155S 155
%NCO (mid-point) % 3.2 4.3 4.3 4.3 5.5 5.5
Curative MOCA MOCA E300 (CA6) MOCA MOCA MOCA
Recommended Stoichiometry % 95 95 95 95 95 95
Mix Ratio Curative per 100 Parts Resin by weight 9.7 12.9 10.4 12.9 16.5 16.5
Resin Temperature °C 75 75 70 – 80 75 70 65
Curative Temperature °C 110 110 40 110 110 105
Recommended Mould Temperature °C 90 90 100 90 90 90
Viscosity @ 100°C cps 770 430 580 430 280 280
Pot life (on a 500g mix) minutes 11 12 10 7 7 5
Recommended Cure Temperature / Time °C / hrs 100 / 16 90 / 16 90 / 16 90 / 16 90 / 16 90 / 16
DIN 2240-91 Shore A 85 90 89 90 94 94
DIN 2240-91 Shore D 37 37 43 43
100% Modulus BS 903 Pt A2 – ISO 37 lb/in²
(Mpa)
790
(5.5)
1260
(8.7)
1320
(9.1)
1730
(11.9)
1820
(12.6)
300% Modulus BS 903 Pt A2 – ISO 37 lb/in²
(Mpa)
1600
(11)
3000
(20.7)
1800
(12.4)
2950
(20.3)
4530
(31.2)
4180
(28.8)
Tensile Strength BS 903 Pt A2 – ISO 37 lb/in²
(Mpa)
5300
(36.6)
6600
(45.5)
4400
(30.4)
6200
(42.7)
6660
(45.9)
6300
(45.9)
Elongation at Break BS 903 Pt A2 – ISO 37 % 530 410 500 400 380 400
Tear Strength BS 903 Pt A3 – ISO 34-1 lb/in
(KN/m)
470
(82.4)
500
(87.7)
440
(77.0)
510
(89.3)
560
(98.0)
570
(99.8)
Compression Set BS903 Pt A6 – ISO 815 % 29 30 29 30 28
Abrasion loss DIN 53516 mm³ 43 34 29 34 31
Resilience ASTM D 2632-92 % 54 43 47 47 44
Specific Gravity g/cm³ 1.06 1.09 1.09 1.09 1.11 1.11

 

 

High Performance Cast Elastomers    
Neuthane 100 Series TDI – PTMEG Ether Prepolymers (95 Shore A)
Neuthane 163S 163S 163
%NCO (mid-point) % 6.3 6.3 6.3
Curative MOCA E300 (CA6) MOCA
Recommended Stoichiometry % 95 95 95
Mix Ratio Curative per 100 Parts Resin by weight 18.9 15.2 18.9
Resin Temperature °C 70 70 70
Curative Temperature °C 110 30 110
Recommended Mould Temperature °C 90 90 90
Viscosity @ 100°C cps 270 270 270
Pot life (on a 500g mix) minutes 5 5 3.5
Recommended Cure Temperature / Time °C / hrs 90 / 16 90 / 16 90 / 16
Hardness DIN 2240-91 Shore A 95 95 95
DIN 2240-91 Shore D 47 47 47
100% Modulus BS 903 Pt A2 – ISO 37 lb/in²
(Mpa)
2250
(15.5)
2210
(15.2)
300% Modulus BS 903 Pt A2 – ISO 37 lb/in²
(Mpa)
5250
(36.2)
3700
(25.5)
5250
(36.2)
Tensile Strength BS 903 Pt A2 – ISO 37 lb/in²
(Mpa)
6580
(45.4)
6700
(46.2)
6580
(45.4)
Elongation at Break BS 903 Pt A2 – ISO 37 % 350 400 400
Tear Strength BS 903 Pt A3 – ISO 34-1 lb/in
(KN/m)
575
(100.6)
660
(115.5)
575
(100.6)
Compression Set BS903 Pt A6 – ISO 815 % 31 32
Abrasion loss DIN 53516 mm³ 36 36
Resilience ASTM D 2632-92 % 44 47
Specific Gravity g/cm³ 1.12 1.12 1.12
High Performance Cast Elastomers    
Neuthane 100LV Series Low Viscosity TDI – PTMEG Ether Prepolymers (80 Shore A – 75 Shore D)
Neuthane 128SLV 143SLV 164LV 164LV 2192LV 2192LV
%NCO (mid-point) % 2.8 4.3 6.4 6.4 9.2 9.2
Curative MOCA MOCA MOCA E300 (CA6) MOCA E300 (CA6)
Recommended Stoichiometry % 95 95 95 95 95 95
Mix Ratio Curative per 100 Parts Resin by weight 8.5 12.9 19.3 15 27.8 22.26
Resin Temperature °C 75 75 65 65 55 55
Curative Temperature °C 110 110 110 30 110 40
Recommended Mould Temperature °C 90 90 90 90 90 90
Viscosity @ 100°C cps 690 250 220 220 150 160
Pot life (on a 500g mix) minutes 18 12 4 2.5 2 1.5
Recommended Cure Temperature / Time °C / hrs 100 / 16 90 / 16 90 / 16 90 / 16 90 / 16 90 / 16
Hardness DIN 2240-91 Shore A 83 90
DIN 2240-91 Shore D 37 65 64 75 70
100% Modulus BS 903 Pt A2 – ISO 37 lb/in²
(Mpa)
700
(4.8)
1260
(8.7)
4100
(27.6)
5450
(37.5)
4100
(28.4)
300% Modulus BS 903 Pt A2 – ISO 37 lb/in²
(Mpa)
1340
(9.2)
2520
(17.4)
6100
(42.0)
7614
(52.5)
Tensile Strength BS 903 Pt A2 – ISO 37 lb/in²
(Mpa)
4150
(28.6)
6400
(44.2)
8100
(55.8)
7614
(52.5)
6150
(42.4)
6300
(43.6)
Elongation at Break BS 903 Pt A2 – ISO 37 % 530 420 280 300 150 225
Tear Strength BS 903 Pt A3 – ISO 34-1 lb/in
(KN/m)
400
(70.1)
480
(84.0)
770
(135.0)
722.2
(127.0)
1050
(7.24)
900
(157.5)
Compression Set BS903 Pt A6 – ISO 815 % 30 31 21 90
Abrasion loss DIN 53516 mm³ 48 35 28 40 29 90
Resilience ASTM D 2632-92 % 54 43 41 38 44 30
Specific Gravity g/cm³ 1.06 1.09 1.14 1.13 1.18 1.18
High Performance Cast Elastomers    
Neuthane 100 Series TDI – PTMEG / PPG Ether Prepolymers (82 – 95 Shore A)

Properties

The Neuthane 100 TDI – PTMEG / PPG ether prepolymers are designed to offer a good level of physical properties at a price advantage over pure TDI – PTMEG systems.

  • a high level of physical properties
  • very good dynamic performance
  • good hydrolysis resistance
  • ease of uselow viscosity
  • choice of normal or long pot life grades
  • hardness range from 70A-95A
  • Wheels (e.g. pallet truck)
  • Medium load roller coverings (e.g. conveyor rollers for the steel industry)
  • Mining and quarrying (e.g. scraper blades)

Processing can be by hand or by dispensing machine

  • Melt prepolymer at 50-70°C for 12-24 hours
  • Heat the prepolymer and curative to the recommended temperature
  • Add pigments and Antifoam, as applicable, whilst mixing
  • It is recommended that air be removed from the prepolymer under vacuum prior to addition of the curative
  • Add the curative and thoroughly mix ensuring that no unmixed material is left on the container sides (if necessary the mix can be transferred to a second clean container and mixed again)
  • Remove air under vacuum
  • Cast into moulds, preheated to the recommended temperature
  • Cure as recommended
  • Avoid prolonged storage of prepolymers at elevated temperatures. This will result in low hardness and lower properties of the cured material
  • Avoid moisture contamination of all materials
  • Part used containers should be flushed with dry nitrogen and resealed immediately after use
  • The development of cure is longer than for pure PTMEG systems so in mould times may need to be extended. Rapid temperature changes during the early stages of cure may result in splits forming in large components.
  • Solvents – ester based systems should be considered: Neuthane 200 [TDI] or Neuthane 700 [MDI]
  • Humid/Wet – MDI or Aliphatic Isocyanate based Systems should be considered: Neuthane 600 [MDI] or Neuthane 500 [Aliphatic]
  • Dynamic – pure PTMEG systems should be considered: Neuthane 100 [TDI] or Neuthane 600 [MDI]
High Performance Cast Elastomers
Neuthane 100 Series TDI – PTMEG / PPG Ether Prepolymers (82 – 95 Shore A)
Neuthane 127 142 142 153 162
%NCO (mid-point) % 2.8 4.3 4.4 5.5 6.3
Curative MOCA MOCA E300 (CA6) MOCA MOCA
Recommended Stoichiometry % 95 95 95 95 95
Mix Ratio Curative per 100 Parts Resin by weight 9.1 13.0 10.6 16.6 19.0
Resin Temperature °C 75 70 70 70 65
Curative Temperature °C 110 110 110 110 110
Recommended Mould Temperature °C 90 90 90 90 90
Viscosity @ 100°C cps 475 285 275 170 140
Pot life (on a 500g mix) minutes 10 10 7 8 4.5
Recommended Cure Temperature / Time °C / hrs 95 / 16 95 / 16 90/16 95 / 16 95 / 16
Hardness DIN 2240-91 Shore A 82 90 88 93 95
DIN 2240-91 Shore D
100% Modulus BS 903 Pt A2 – ISO 37 lb/in²
(Mpa)
640
(4.4)
1150
(7.9)
1060
(7.3)
1630
(11.2)
1900
(13.1)
300% Modulus BS 903 Pt A2 – ISO 37 lb/in²
(Mpa)
1000
(6.9)
2180
(15.0)
1580
(10.9)
3470
(23.9)
4720
(32.5)
Tensile Strength BS 903 Pt A2 – ISO 37 lb/in²
(Mpa)
3500
(24.1)
5050
(34.8)
3740
(25.7)
5990
(41.3)
6000
(41.4)
Elongation at Break BS 903 Pt A2 – ISO 37 % 700 450 508 390 340
Tear Strength BS 903 Pt A3 – ISO 34-1 lb/in
(KN/m)
380
(66.5)
400
(70.1)
36
(6.3)
430
(75.3)
460
(80.8)
Compression Set BS903 Pt A6 – ISO 815 % 32 39 52 42 41
Abrasion loss DIN 53516 mm³ 83 55 101 61 70
Resilience ASTM D 2632-92 % 54 40 33 32 39
Specific Gravity g/cm³ 1.06 1.09 1.07 1.12 1.12

 

Clear
High Performance Cast Elastomers
Neuthane 2100 Series 

Properties

The Neuthane 2100 series are low-odour, high perfomance TDI – PTMEG ether prepolymers designed to produce items for use in arduous application areas.

  • low levels of free isocyanate
  • a high level of physical properties
  • very good dynamic performance
  • good hydrolysis resistance
  • ease of use
  • low viscosity
  • hardness range from 85A-95A*

* Lower hardness can be obtained with Neuthane CA curatives. (Details available upon request)

  • Wheels (e.g. fork truck, pallet truck and press on bands)
  • High load roller coverings (e.g. steel & paper industry)
  • Mining and quarrying (e.g. screen decks, pipe lining)
  • Hydrocyclones
  • Oil and gas industry (e.g. gaskets)
  • Automotive (e.g. suspension bushes)
  • Metal Finishing (e.g. vibration bowls)

Processing can be by hand or by dispensing machine

  • Melt prepolymer at 50-70°C for 12-24 hours (as a guide the grades with the lower NCO value will take longer to melt than those with higher NCO values)
  • Heat the prepolymer and curative to the  recommended temperature
  • Add pigments and Antifoam, as applicable, whilst mixing
  • It is recommended that air be removed from the prepolymer under vacuum prior to addition of the curative
  • Add the curative and thoroughly mix ensuring that no unmixed material is left on the container sides (if necessary the mix can be transferred to a second clean container and mixed again)
  • Remove air under vacuum
  • Cast into moulds, preheated to the recommended temperature
  • Cure as recommended
  • Avoid prolonged storage of prepolymers at elevated temperatures. This will result in low hardness and lower properties of the cured material
  • Avoid moisture contamination of all materials
  • Part used containers should be flushed with dry nitrogen and resealed immediately after use
  • Solvents – ester based systems should be considered: Neuthane 200 [TDI] or Neuthane 700 [MDI]
  • Humid/Wet – MDI or Aliphatic Isocyanate based Systems should be considered: Neuthane 600 [MDI] or Neuthane 500 [Aliphatic]
  • Resilience – improvements can be achieved with MDI based systems: Neuthane 600HR [Prepolymer]
  • Cost – Neuthane 100 [PTMEG/PPG], Neuthane 300
    [PPG] or Neuthane 200 [Ester] can be considered
High Performance Cast Elastomers
Neuthane 2100 Series Low Odour TDI – PTMEG Ether Prepolymers (85 – 95 Shore A – 47 Shore D)
Neuthane 2132 2143 2155 2163
%NCO (mid-point) % 3.2 4.3 5.5 6.3
Curative MOCA MOCA MOCA MOCA
Recommended Stoichiometry % 95 95 95 95
Mix Ratio Curative per 100 Parts Resin by weight 9.7 13.0 16.6 19.0
Resin Temperature °C 80 70 70 70
Curative Temperature °C 110 110 110 110
Recommended Mould Temperature °C 90 90 90 90
Viscosity @ 100°C cps 670 430 265 250
Pot life (on a 500g mix) minutes 17 10 7 5
Recommended Cure Temperature / Time °C / hrs 100 / 16 90 / 16 90 / 16 90 / 16
Hardness DIN 2240-91 Shore A 85 90 94 95
DIN 2240-91 Shore D 37 43 47
100% Modulus BS 903 Pt A2 – ISO 37 lb/in²
(Mpa)
915
(6.3)
1320
(9.1)
1850
(12.8)
2660
(18.4)
300% Modulus BS 903 Pt A2 – ISO 37 lb/in²
(Mpa)
1730
(11.9)
2250
(15.5)
400
(27.6)
5810
(40.0)
Tensile Strength BS 903 Pt A2 – ISO 37 lb/in²
(Mpa)
5650
(38.9)
6910
(47.7)
6970
(48.1)
7100
(49.0)
Elongation at Break BS 903 Pt A2 – ISO 37 % 490 400 380 380
Tear Strength BS 903 Pt A3 – ISO 34-1 lb/in
(KN/m)
450
(78.9)
490
(85.6)
450
(78.9)
610
(106.9)
Compression Set BS903 Pt A6 – ISO 815 % 30 31 30 28
Abrasion loss DIN 53516 mm³ 40 34 35 41
Resilience ASTM D 2632-92 % 55 44 47 44
Specific Gravity g/cm³ 1.06 1.10 1.11 1.12

Information contained in the data is, to the best of our knowledge, true and accurate. Since conditions of use are beyond our control, no warranty is given or implied in respect of any recommendations or suggestions made by ourselves, nor is freedom from patent infringement inferred.